• CE認證

• Accuracy of 0.01% of full scale ± 1 count.

• Update rate to 60/sec in 60 Hz noise environments or 50/sec in 50 Hz noise environments.

• Full-scale range from 20.000 mV full scale (1 μV resolution) to 500.00 mV full scale (10 μV resolution).

• Isolated transducer excitation output. 5V at 100mA or 10V at 120mA as selected by TEDS. In non-TEDS operation, the excitation is always 10V.

• Isolated 4-20 mA, 0-20 mA or 0-10V analog output.

• Isolated serial data transmitter output. The transmitter serial port is default jumpered for RS232 or full-duplex RS485 (same jumper settings).

• Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and com-munications.

• Internal jumpers are used to select the signal range, communication type, and exci?tation level.

• Transmitter setup is via serial connection to a PC using MS Windows based Instrument Setup Software plus TEDS IEEE 1451.4 when detected. 

Full scale ranges 20.000 mV, 50.000 mV, 100.00 mV, 250.00 mV, 500.00 mV

Input resistance 1 Gohm

Input accuracy at 25°C ± 0.01% of full span ±2 counts

Max applied voltage 35V

Excitation level (factory default) 10 Vdc ± 5%, 120 mA

Other excitation levels (jumper selectable) 5 Vdc ± 5%, 100 mA; 24 Vdc ± 5%, 50 mA

Output Isolation 50 Vdc to meter ground

Conversion rate 60/second (setting for 60 Hz noise rejection)

Input resolution 16 bits (65,536 steps)

CMV, DC to 60 Hz 250V RMS

CMR, DC to 60 Hz 130 dB

NMR at 50/60 Hz 90 dB with no digital filtering

Input filtering User-selectable digital time constants from 80 ms to 9.6 s

Selection of signal ranges Jumpers on signal conditioner board

Selection of serial format, excitation output, analog output Jumpers on main board

Programming Via PC using Instrument Setup software and serial cable

Standards compliance TEDS IEEE 1451.4

Software support TEDS Reader_Editor Software (available as an accessory

Output levels 4-20 mA, 0-20 mA or 0-10V

Compliance at 20 mA 10V (0 to 500 ohm load)

Compliance at 10V 2 mA (5 kohm load or higher)

Output resolution 16 bits (65,536 steps)

Output accuracy ±0.02% of full span

Output isolation Safety rated to 250 Vrms, 4.2 kV per High Voltage Test

Serial formats RS232 or RS485 (half or full duplex), user selectable

Serial protocol Custom ASCII or Modbus (RTU or ASCII)

Modbus Compliance Modbus over Serial Line Specification V1.0 (2002)

Serial connector Detachable screw terminal plugs

Baud rates 300, 600, 1200, 2400, 4800, 9600, 19200 baud

Output isolation Safety rated to 250 Vrms, 4.2 kV per High Voltage Test

Relay type Two solid state relays, SPST, normally open, Form A

Load rating 120 mA at 130 Vac or 170 Vdc, 28 ohms series resistance

Power to Transmitter (standard power) 85-264 Vac or 90-300 Vdc

Power to Transmitter (low voltage power option) 12-32 Vac or 10-48 Vdc

Power Isolation Safety rated to 250 Vrms, 4.2 kV per High Voltage Test

Case dimensions 120 x 101 x 22.5 mm

Case mounting 35 mm DIN rail per EN 50022

Electrical connections Detachable screw plug connectors

Operating temperature 0°C to 70°C

BStorage temperature -40°C to 85°C

Relative humidity 95% from 0°C to 40°C, non-condensing

訂貨型號

Order Code Model Capacity Range Description

SST-HV N/A Smart Sensor Transmitter

Accessories

SST-RS232AD9 N/A SST-RS232AD9 Cable

SST-USBAD9 N/A Serial to USB Adapter Cable & Disk

配件

DPM-3-AD9 N/A Adapter Connector

DPM-3-PC6 N/A 6 Foot Power Cable

DPM-3-PC12 N/A 12 Foot Power Cable

DPM-3-TRES N/A TEDS Reader Editor Software

DPM-3-DLS N/A Data Logging Software 

相關型號

SST-LV

SSI

DPM-3