YD9230/SDJ-706/BSZ808AVS-2振動烈度傳感器

BSZ808A Integrated Vibration Transmitter

一、產品簡介

YD9230/SDJ-706/BSZ808AVS-2振動烈度傳感器將磁電式振動傳感器、精密測量電路集成在一起，構成高精度振動測量系統，該變送器可直接連接DCS、PLC或其它設備，是測量風機、動機、水泵等工廠設備振動的理想選擇。

I. Product Introduction

The PR-5020 integrated vibration transmitter integrates a magnetoelectric vibration sensor and precision measurement circuits to form a high-precision vibration measurement system. It can be directly connected to DCS, PLC and other equipment, serving as an ideal solution for vibration monitoring of industrial equipment such as fans, motors and water pumps.

二、技術參數

2．1 頻率響應：10 ～ 1000 Hz  *  或者5 ～ 1000 Hz（特殊說明）

2．2 自振頻率：10Hz

2．3 量程范圍：

振動加速度量程1～5g峰值；

   振動速度量程0～100mm/s有效值（可選）；常規機械選0-20mm/s，對應輸出：4-20mA;

   振動位移量程0～1900μm峰峰值（可選）：風機等設備常用0-200um，對應輸出：4-20mA ；

2．4 輸出電流：4～20mA（可選1-5V，0-10V，RS485，Hart協議）

2．5輸出阻抗：≤500Ω

2．6工作電壓：DC12-24V±10%

2. 7接線方式：二線制

2．7最大加速度：10g

2．8測量方向:通用(垂直或水平)

2．9 使用環境：溫   度  -40℃～80℃ 相對濕度 ≤90%

2．10 外形尺寸：φ34mm×76mm

2．11 安裝方式：M10*1.5螺釘 或其他規格 或是磁吸安裝

2．12 重    量： 約350g

2. 13 外殼材質:304 不銹鋼

II. Technical Parameters

2.1 Frequency Response: 10 ～ 1000 Hz, or 5 ～ 1000 Hz (special specification)

2.2 Natural Frequency: 10 Hz

2.3 Measuring Range:Vibration acceleration: 1～5g (Peak);

Vibration velocity: 0～100 mm/s (RMS, optional); 0-20 mm/s for general machinery, corresponding output: 4-20 mA;

Vibration displacement: 0～1900 μm (Peak-Peak, optional); 0-200 μm commonly used for fans and other equipment, corresponding output: 4-20 mA;

2.4 Output Signal: 4～20 mA (optional: 1-5V, 0-10V, RS485, HART protocol)

2.5 Output Impedance: ≤500 Ω

2.6 Operating Voltage: DC 12-24V±10%2.7 Wiring Mode: Two-wire system

2.8 Maximum Acceleration: 10 g

2.9 Measuring Direction: Universal (vertical or horizontal)

2.10 Operating Environment:Temperature: -40℃～80℃Relative Humidity: ≤90%

2.11 Overall Dimension: φ34mm×76mm

2.12 Installation Method: M10×1.5 screw, other specifications or magnetic mounting

2.13 Weight: Approx. 350 g

2.14 Housing Material: 304 Stainless Steel

三、安裝說明

3．1 安裝位置： 垂直或水平安裝于被測振動點上，將傳感器底部磁吸式或螺釘式固定在被測殼體上，然后將傳器擰在上面擰緊即可。

3．2 安裝尺寸及規范：若變送器安裝位置受到高溫蒸汽等沖刷時，為降低變送器環境溫度、需加防護措施，一般情況下可不加防護。振動變送器的防護參看下圖。

3．3 接線說明：棕色導線接DC24V電源正端，黑色導線接4-20mA輸出。連接導線要求有良好的絕緣性能，采用二芯屏蔽電纜。

棕色導線接DC24V電源正端，藍色導線接4-20mA輸出正端，黃綠色線為屏蔽線。

III. Installation Instructions

3.1 Installation PositionInstall vertically or horizontally at the measured vibration point. Fix the sensor base on the measured housing by magnetic attraction or screw fastening, then screw and fasten the sensor tightly.

3.2 Installation Dimensions and SpecificationsIf the transmitter is exposed to scouring by high-temperature steam or other harsh conditions, protective measures shall be taken to reduce the ambient temperature of the transmitter; no protection is required under normal conditions. Refer to the figure below for the protection of the vibration transmitter.

3.3 Wiring InstructionsThe brown wire connects to the positive terminal of DC 24V power supply, and the black wire connects to the 4-20mA output. The connecting wires shall feature good insulation performance, and two-core shielded cables shall be adopted.

The brown wire connects to the positive terminal of DC 24V power supply, the blue wire connects to the positive terminal of 4-20mA output, and the yellow-green wire is the shielding wire.

四、注意事項

4．1 變送器應防止劇烈碰幢和敲打。

4．2 運輸過程和貯存時應置于專用包裝盒內。

IV. Precautions

4.1 The transmitter shall be protected from severe collision and knocking.

4.2 During transportation and storage, the product shall be placed in the dedicated packaging box.